As the name states this is a place for general tips and tricks if you have something you would like to share let us know but please keep this thread on topic.
Tips and Tricks
1. When working on your SxS, ATV, or anything driven offroad always use a thread locker on all nuts and bolts whether it be an added accessory or a maintenance item. But be careful only use small amounts of the recommended locker. As a general rule I use blue thread locker on smaller bolts and red thread locker on larger bolts(like axle nuts).
2. After a good clean up of your SxS or ATV use a good Plastic Protectant (such as armor all) to spay it down all over then let it set for an hour or so without wiping it off. It will keep you bike looking like new and easier to clean next time.
3. When mud riding run a little more air pressure in your tires it will yield much needed ground clearance. Plus lower air pressures will allow mud and debris to get between the bead of the tire and rim eventually causing a flat.
4. Always Carry tire plugs and some kind of pump to inflate the tires in case of a flat. It is also a good ideal to carry a ratchet tie-down or rope in case of the bead breaking from the rim. The ratchet tie down or rope can be wound around the tire to force the bead back on.
5. When towing another vehicle out of the mud or out of the trails always attach your tow strap at a low point on both vehicles approximately the same height as the axle. That gives you the most pulling strength.
6. If you have a winch on you SxS or ATV be sure and spray cable lube on it every time you clean your Ride to keep the cable looking and performing like new. Reeling it all the way out, cleaning it, and lubing it every time you use it when submerged in mud is also a good Preventive maintenance.
7. When changes exhaust always and I mean always re-jet your carburetor it will give you more power and make your engine last longer.
8. Always check the gap on a new spark plug. They may say pre-gapped but in transit that gap could change.
9. Preventative maintenance doesn't just mean changing the oil. Every time you clean your bike check your coolant, ball joints, Tie rods, wheel bearing, lug nuts, and clean your air filter.
10. Before buying anything for your SxS or ATV always do a little research to find the parts that best suit your needs. This is so your "wish I hadn't done that" list is smaller than your "Glad I did" list.
11. If you have a rhino and the bed is getting scratched a truck bed coating like Herculiner will fix that problem as well as get rid of a lot of the vibrating noise caused by the bed.
12. When installing graphics clean the plastic then apply a mixture of soap and water to the plastic where the graphics will be applied this keeps the graphics from sticking so you can move it around and put it where you want it. When you have the graphics where you want them you can either let them set and air dry or you can speed up
the process with a little heat from a hair dryer. Remember to always apply graphics in a warm environment.
13. Have you ever stressed the plastic on your bike? Bending your plastic beyond a specific point causes stress marks which are eye sores on any bike, but can be fixed to an extent with a heat gun. But be careful not to get the plastic to hot.
14. If your oil cooler is in front of your radiator then you know it is almost impossible to clean the radiator without removing the oil cooler. But I have a solution for that, This is a handy little item that is real simple and will allow you to give the radiator a good cleaning in only minutes every-time you wash your bike.
15. Are you tired of having to bear hug the hood of you Rhino every time you need it open? If so this mod. is for you and only takes a few seconds with a Dremel tool. Click this link for more info Rhino easy open Hood Mod.http://www.mudandgutsoffroad.org/rhino-hood-mod-
16. It is a good ideal to go over a new bike and put Dielectric grease on all of its electrical connections. After that any time you unplug something electrical on your quad make sure it has sufficient Dielectric grease on it to keep it from shorting out later on the trail.
17. If your bike has non-directional tires it is also a good Ideal to rotate them from side to side when they start to get a rounded edge to keep a sharp leading edge on the tires so they bite just a little bit harder.
18. If your bike has a fuel petcock always remember to turn it off when not in use. Because if it leaks not only will it cause your bike to flood it could do major engine damage if not found in time.
19. Never use fabric filter oil (such as K&N filter oil) on a foam filter it is not designed for it. Always use foam filter oil on a foam filter and fabric filter oil on fabric filters.
20. When removing the float bowl on your carb. be very careful most float bowl screws are very soft and easy to strip out. I recommend replacing them with socket head cap screws (a common Yamaha float bowl screw is 4mm x 10mm).
21. In need of a fuel filter for your Rhino? NAPA Gold 3011 is a quick replacement for the stock Yamaha Rhino filter (450 and 660).
22. If you ride offroad invest in a set of shock covers they are cheap insurance for those expensive shocks.
23. If you find yourself changing wheel bearings which are recessed into the hub and you need a quick tool to press them in, grind the outer radius on one of your old bearings till it fits freely in the hub and use it as a bearing driver.
24. To make it easier to press in a bearing put the bearing in the freezer for a couple hours before installing. The cold temp will cause the steel to shrink making it easier to install.
25. Do not use Dot 3 brake fluid in a system that calls for Dot 4. Dot 4 fluid has a higher Temperature rating than Dot 3 by about 80 degrees.
26. Another good item to keep with you on the trails is TP(toilet paper).
27. Like the Yamaha Rhino a lot of bikes have caliber slides which will become stuck over time if you ride in mud and water. I recommend removing these atleast once or twice a year and greasing them to prevent them from sticking. If you wait till they stick the job will be a lot harder and your brakes could potential fail when on the trail.
28. When mounting a new set of tires lubing up the bead of the tire with a little dish-washing liquid will make the tire slide on the rim easier and it will also allow the bead to seat on the rim with a little less pressure. Never use anything other than dish-washing liquid or approved fluids.
29. To extend the life of your ball joints and tie rods purchase a grease needle from the local auto parts store. The grease needle can be slide between the seal and metal parts to allow greasing if it is not equipped with a grease Zerk. The needle is designed so you can poke a small hole in the seal then grease but I do not recommend poking a hole in any seals when used offroad.