grizzly 550/700 hids

im fixing to put hids on my grizzly i was just wondering if you put hids on yours how you run the wires thru the boot that covers the light if you cut the boot how did you seal it thanks

there is already a hole there for the wires to run through

yes they are holes in the boot but my hids have a plug on them the hole in the boot is for wires they are not for a plug to fit thru thats why i was wondering if anyone put hids on theirs i was wondering how they run the wires if they cut the boot for the plug how dig they seal it or how they run the wires

i finally got off my butt and installed my hids they was three wires run thru the inner boot all seperate i just cut a small round piece containing the three wires out and pullued the square factory plug thru it didnt know if it would stretch that much but it did i could have pulled the spades out but didnt wanna take the time installed the hid bulbs run the hid wires thru the hole and put some permatex on it real good let dry over night then put the outter boot back on wired them up mounted the ballast under the hood

you will love them if they are good quality, HID's put out a lot more light then the factory lights do..

What's a good brand of hids to get? I want something that's plug n play. I don't know which ones are good and which ones are junk. And input would be appreciated.

QuadBoss HID's are Vision X I think and they are a good quality replacement, I have been debating on replcing the ones on the RZR with them..

I get all of my Hid's for of my vehicles and wheelers from DDM Tuning.
I have never had any issues at all. Lifetime warranty. Great prices too!

Guy's wouldn't it be better to go with led's? Most only draw a fraction of a hid lights. It's a lot easier on you charging system also.

Bluedevil wrote:

Guy's wouldn't it be better to go with led's? Most only draw a fraction of a hid lights. It's a lot easier on you charging system also.

I think it is. I have a 10" Rigid bar and you couldn't tell my hid lights were on when it was running. I took them off and sold them and put the stockers back in.

For the money the hids do me just fine. The hids draw less than the stock bulds do.

for stock replacments (that I know of) most companies do not offer led's. Polaris offers LED's for the RZR but HID's are a LOT cheaper and work about the same. I have considered HID's for the stock replacements on the RZR but have not broke down and done it yet.. I do have two Baja Designs Squadrons on the front bumper that offer amazing light output (leds)..

Rigid Industries LED's is what I run. A set of D2's and a SR-10 bar in the front a Dually flood for a reverse light. I can't even tell the sun went down...lol

i agree leds have better light output but the ones i have and the most i have seen blind oncoming people so bad it makes it dangerous to pass at speed where as hids dont as bad and hids are a great improveent over stock bulbs almost like going from hids to leds about the best price hids ive seen are ddm

Anyone running LED's probably should turn them off when approaching oncoming traffic. I know everyone in our group always do. I had thought about buying Kawi LED headlights for my T4, but didn't want to blind oncoming traffic especially since we ride the road to the trucks at night occasionally.

I hooked mine up with the high beams so I can switch to low when I meet someone, But if I'm running in a group I don't like using them cause I will blind anyone in front if me. I just have a 18" led light bar. It put out 2900 lumes. I plan on getting some flood leds for the front also so I can light em up when I need to see.

I got mine through ddm does anyone have any install picks or instructions? They only sent me one bulb I guess one kit, so I'm trying to get that straightened out. But the one bulb came with two wiring harness's. one has a square box with a red fuse and a 3 prong plug, the other looks like a ballast with two plugs on it. Any help is apprecited

post a picture of what you got i think i had a 3 prong plug that connected to one of the factory headlight plugs you will need 2 ballast one for each bulb and the wiring that connects them and has a hot and ground you will need to hook up the way i got mine mounted i cant get any pictures that woul help you good luck

I tried but don't know how to post a pic on here.

i think you have to host with photo bucket flicker or some other site you should find what you need on youtube also i seen a few on it last night when i was trying to find a picture to help explain

Hausscatgrizz wrote:

I got mine through ddm does anyone have any install picks or instructions? They only sent me one bulb I guess one kit, so I'm trying to get that straightened out. But the one bulb came with two wiring harness's. one has a square box with a red fuse and a 3 prong plug, the other looks like a ballast with two plugs on it. Any help is apprecited

 
Aaron, did you order the single motorcycle kit Hi & Low beam? Did it look like this?
 

 
 
 
This is what you need. Dual motorcycle kit Low Beam. The bulb is a H4  I use the 5k color. I have just low beam and mine are almost 4 years old with zero problems. With the type headlight housing the Grizzly has, the Hi- Low kit is a waste due to it not having a reflective lens in the housing.
 

 
Call me or send me a pic of the kit you have, with your phone and we'll go from there. 1-270-543-0500

I ordered the high/low kit 35w

My bulb didnt have that plastic case around it. It just had some foam and a metal reflector around it

Hausscatgrizz wrote:

My bulb didnt have that plastic case around it. It just had some foam and a metal reflector around it

Give me a call...